STEEL TECHNICAL RESOURCES

Steel Specifications, Weight & Procurement References

Bao Steel (Qingdao) Co., Ltd. is a steel manufacturer with its own mills, producing and supplying carbon steel, stainless steel, coated steel, structural sections, rebar and wire. Use these technical references to prepare material grades, dimensions, estimated weights and inspection requirements before requesting a quotation.

Own-mill production 50,000+ global customers Export steel supply
Steel plate and coil technical inspection at Bao Steel (Qingdao) Co., Ltd.
10 Million TonnesAnnual production from our own mills
500,000 TonnesYear-round stock inventory
50,000+Customers worldwide
STEEL WEIGHT CALCULATION

Estimate theoretical steel weight before ordering

Use the formulas below for preliminary quantity planning. The examples use a nominal carbon steel density of 7,850 kg/m³. Stainless, alloy and coated products require the applicable material density and product details.

Steel Plate

Flat Product

Length and width in metres; thickness in millimetres.

Weight (kg) = L × W × T × 7.85 Example: 6 m × 1.5 m × 10 mm = 706.5 kg

Carbon Steel Plate · Stainless Steel Plate

Round Bar

Long Product

Diameter in millimetres; result is kilograms per metre.

Weight (kg/m) = D² × 0.006165 Example: 50 mm round bar ≈ 15.41 kg/m

Carbon Steel Bar · Alloy Steel Bar

Flat & Square Bar

Section Bar

Width, thickness or side length in millimetres; result is kilograms per metre.

Flat: W × T × 0.00785
Square: A² × 0.00785
Example: 50 × 10 mm flat bar ≈ 3.93 kg/m

Carbon Steel Bar

Steel Pipe

Tubular Product

Outside diameter D and wall thickness T in millimetres; result is kilograms per metre.

Weight (kg/m) = 0.02466 × T × (D − T) Example: 114.3 mm OD × 6.02 mm WT ≈ 16.07 kg/m

Steel Pipe · Carbon Steel Pipe

Steel Coil

Coiled Product

Outside diameter, inside diameter and width in metres; density in kg/m³.

Weight (kg) ≈ π ÷ 4 × (OD² − ID²) × W × 7,850 Use measured coil dimensions for a preliminary estimate.

Hot Rolled Coil · Cold Rolled Coil

Rebar

Reinforcing Bar

For a nominal round section, use the round-bar formula as a theoretical estimate. Rib geometry and standard mass tolerances apply.

Nominal Weight (kg/m) ≈ D² × 0.006165 Confirm nominal mass per metre against the governing rebar standard.

Steel Rebar · BS 4449 Rebar

Weight calculation: These formulas provide theoretical estimates, not guaranteed shipping weights. Actual mass can vary with material density, dimensional tolerances, product standards, coating, scale measurement and packing. Confirm the commercial quantity and final weight against the mill records and shipping documents.
STEEL GRADE REFERENCE

Common steel grades and product standards

Select the product form first, then confirm the grade, governing standard, delivery condition and mechanical requirements. Similar grade names across different standards are not automatic equivalents.

Steel plate thickness and dimensional inspection on a factory inspection table
PLATE DIMENSIONS & TOLERANCES

Steel plate thickness, width and dimensional tolerance

Plate tolerance depends on the governing product standard, nominal thickness, width, length, edge condition and delivery specification. Structural plate, pressure vessel plate and stainless plate follow different general requirements and dimensional provisions.

  • Confirm nominal thickness, width, length and ordered quantity.
  • Identify the applicable product standard and tolerance standard.
  • State whether the order requires trimmed or mill edges.
  • Confirm flatness, surface condition and any additional inspection.
  • For pressure vessel and project plate, include the design code and supplementary requirements.

Common reference standards include ASTM A6/A6M for structural steel products, ASTM A20/A20M for pressure vessel plates, ASTM A480/A480M for stainless flat-rolled products and EN 10029 for hot-rolled steel plates. The applicable edition and product-specific requirements govern the order.

STEEL COIL SPECIFICATIONS

What to include in a steel coil specification

A complete coil enquiry identifies the steel grade and standard together with dimensions, coil configuration, surface condition and any metallic or paint coating requirements.

Hot-rolled, cold-rolled and coated coil details

  • Steel grade and product standard, such as ASTM A1011, A1018 or A1008.
  • Nominal thickness and width, with required dimensional tolerances.
  • Coil inside diameter, outside diameter and maximum coil weight.
  • Hot-rolled, pickled and oiled, cold-rolled or annealed surface condition.
  • For galvanized or galvalume coil, coating designation and coating mass.
  • For PPGI or PPGL, paint system, coating thickness, colour reference and top/back coating requirements.
  • Oiling, passivation, surface finish, edge condition and packaging requirements.
Hot rolled, cold rolled and coated steel coils arranged in a steel production facility
PIPE SCHEDULE & DIMENSIONS

Pipe NPS, outside diameter and schedule reference

Pipe schedules identify a wall-thickness series for a nominal pipe size. The schedule number alone does not state the wall thickness; the corresponding value depends on nominal size and the applicable dimensional standard.

Steel pipe end and wall thickness inspection with pipe dimensions visible

Specify the complete pipe dimensions

For an accurate pipe quotation, provide the nominal pipe size (NPS or DN), outside diameter, wall thickness or schedule, length, grade, product standard and end preparation. Confirm whether the order requires plain ends, bevelled ends, threaded ends or a coating.

  • NPS / DN: nominal size designation.
  • Outside diameter (OD): specified pipe outside diameter.
  • Wall thickness (WT): nominal wall thickness in millimetres.
  • Schedule: wall-thickness series for the specified nominal size.
  • Length and tolerance: fixed, random or project-specific length.
  • End condition: plain, bevelled, threaded or coupled where specified.
Pipe ordering: State both schedule and wall thickness when the project specification requires a specific WT. Confirm the dimensional table under the selected ASTM, API or other governing pipe standard.
REBAR STANDARDS

BS 4449, ASTM and HRB rebar specifications

Rebar standards define strength, ductility, test methods, dimensions and mass requirements. Confirm the required grade and class against the project's design specification and destination market.

Reinforcing bar grades in our supply range

  • BS 4449: B500A, B500B and B500C, with different ductility classes.
  • GB: HRB400 / HRB400E and HRB500 / HRB500E.
  • ASTM: ASTM A615 rebar and ASTM A706 Grade 60.
  • TMT: Fe500D rebar.

For an RFQ, specify the standard and grade, nominal diameter, bar length or coil form, quantity, required test documents and destination. Do not treat grade designations from different standards as interchangeable without checking the specified mechanical and ductility requirements.

Ribbed reinforcing steel bars undergoing dimensional and mechanical quality inspection
MTC & INSPECTION DOCUMENTS

Mill test certificates and order traceability

Bao Steel (Qingdao) Co., Ltd. supplies mill test certificates for ordered steel according to the applicable product standard and agreed inspection requirements.

Steel mill test certificate and heat number traceability records for an order

Information to check on an MTC

  • Manufacturer and product identification.
  • Steel grade, product standard and delivery condition.
  • Heat or cast number and supplied quantity.
  • Chemical composition and specified mechanical test results.
  • Impact, hardness, bend, hydrostatic or NDT results where required.
  • Certificate type and validation details.

Where the purchase order specifies EN 10204 3.1 or 3.2, the certificate type and inspection parties must be agreed before the inspection. Third-party inspection by SGS, Bureau Veritas (BV), TÜV or a buyer-nominated agency can be coordinated to the agreed scope.

STEEL PROCUREMENT GUIDE

Prepare a complete steel RFQ

A clear material schedule helps our team check mill production, stock availability, technical requirements and export arrangements against the same specification.

01 / PRODUCT

Identify the Material

State product form, grade, standard, application and delivery condition.

02 / DIMENSIONS

Confirm the Size

Provide thickness, width, length, diameter, wall thickness or section designation, including tolerances.

03 / QUANTITY

Set the Order Quantity

Give total tonnes, pieces, bundles or coils, plus any size breakdown or split-delivery plan.

04 / DELIVERY

Define Delivery Needs

Specify inspection documents, packing, destination port, Incoterms and required delivery date.

Production, stock and delivery planning

Our own mills produce 10 million tonnes of steel annually, supported by a year-round stock inventory of 500,000 tonnes. We review each enquiry against the specified grade, dimensions, quantity, inspection requirements and delivery schedule.

For items confirmed from stock, dispatch is typically arranged within 10 days. Sample lead time is generally 7–14 days. Final timing is confirmed against the material, any required processing or inspection, packing and destination.

Steel orders organized by grade and dimensions for export packing and shipment
Send your material list: Attach an Excel schedule, drawing, technical specification or purchase list to your enquiry. Include the destination port and required delivery date so we can review the complete order.
TECHNICAL RESOURCE FAQ

Steel specification and procurement questions

For a product-specific quotation, send the governing standard and full dimensions with your material list.

How do I calculate the weight of a steel plate?
For a preliminary carbon steel estimate, multiply length in metres × width in metres × thickness in millimetres × 7.85. A 6 m × 1.5 m × 10 mm plate is approximately 706.5 kg. Confirm final mass against the actual dimensions, tolerance and mill weight records.
Are steel grades with similar names equivalent?
Not automatically. Grade comparison must consider the governing standard, chemical composition, mechanical properties, delivery condition, testing and application requirements. State the exact standard and grade in your RFQ.
What information is needed to quote steel coil?
Provide grade and standard, thickness, width, coil ID and maximum coil weight, surface condition and quantity. For galvanized, galvalume, PPGI or PPGL, also state coating designation, coating mass or paint system requirements.
Does pipe schedule specify the actual wall thickness?
The schedule identifies a wall-thickness series for a nominal pipe size. The corresponding wall thickness varies with nominal size. Provide NPS or DN, outside diameter, schedule or required wall thickness, length, grade and product standard.
Can Bao Steel provide MTC and third-party inspection?
Yes. Bao Steel (Qingdao) Co., Ltd. provides MTC documentation for ordered steel and coordinates SGS, BV, TÜV or buyer-nominated inspection according to the agreed purchase order and inspection scope. See Certifications.
How soon can stocked steel be dispatched?
Stock orders are typically arranged for dispatch within 10 days after order details and requirements are confirmed. Samples generally take 7–14 days. The final schedule depends on the grade, dimensions, inspection, packing and destination. See Stock & Supply.
SEND YOUR STEEL REQUIREMENTS

Need a price for your steel specification?

Send the grade, standard, dimensions, quantity and destination port. Bao Steel (Qingdao) Co., Ltd. will review the material requirements and prepare a quotation.

REQUEST A QUOTE

Share your specifications or upload a purchase list. We will review the details and get back to you.


    PDF, Word, Excel, JPG or PNG. Max. 10 MB.

    Your contact information is used to respond to your inquiry. Privacy Policy.

    BAO STEEL (QINGDAO) CO., LTD. Direct factory contact · Qingdao, China
    WhatsApp