Material Quality & Traceability

Steel Quality Control, Testing & MTC

Bao Steel (Qingdao) checks material identity, dimensions, test results and delivery condition against the agreed purchase specification. Our quality control covers steel plate, coil, rebar, wire, bars, structural sections and pipe produced at our mills.

Grade & standard reviewMill Test CertificatesThird-party inspection on request
Quality inspection station with finished steel plate and inspection equipment
Mill Test CertificatesMaterial results and heat references linked to the supplied order.
SGS · BV · TÜVIndependent inspection can be arranged to match agreed order terms.
ISO 9001Quality management certification within the certified entity and scope.

Order-Based Acceptance

The inspection plan starts with the ordered specification.

Acceptance criteria differ by steel grade, product form, thickness and service requirement. The applicable ASTM, EN, JIS, GB or other contract standard defines what must be checked and how results are reported.

01

Review the order

Confirm grade, standard edition, size range, tolerances, delivery state and requested documents.

02

Identify the material

Link production or stock material with its heat, test unit, grade and supply records.

03

Check required properties

Carry out applicable composition, mechanical, dimensional, coating or non-destructive tests.

04

Release for delivery

Review results, material identity, packing requirements and the inspection documents.

Laboratory Testing

Chemistry and mechanical results checked by grade.

The ordered steel specification determines sampling, test units, methods and acceptance limits. Results are recorded against the corresponding heat, batch or test unit.

Metal sample undergoing optical emission spectroscopy for steel chemical analysis

Chemical Composition

Confirm the specified alloy content.

Heat or product analysis is checked as required by the material standard. Carbon, manganese, silicon, phosphorus and sulfur are important for many carbon steels; stainless and alloy grades also require attention to elements such as chromium, nickel and molybdenum.

Heat analysisProduct analysis where specifiedGrade verification
Standard steel tensile specimen held by the upper and lower grips of a testing machine

Mechanical Properties

Verify strength and forming performance.

Tensile tests provide yield or proof strength, tensile strength and elongation where required. Bend, rebend, hardness and impact tests are selected for the product and its service conditions, rather than applied uniformly to every order.

Tensile testsBend / rebendImpact or hardness when applicable

Product-Specific Inspection

Different steel products call for different checks.

Vessel plate, galvanized coil and reinforcing bar each have their own inspection requirements. Acceptance follows the product standard and the agreed order terms.

02 / COIL

Hot & cold rolled coil

Thickness, width, edge quality, surface finish, coil condition and applicable mechanical performance are checked against the specified grade and delivery state.

03 / COATING

Galvanized & prepainted products

Metallic coating mass or thickness, paint film, finish and surface appearance are assessed by the method required in the order. Coating adhesion or bend performance is tested where relevant.

04 / REBAR

Reinforcing steel

Nominal diameter, mass per metre, rib geometry and tensile properties are considered together. Bend or rebend requirements follow the applicable BS 4449, ASTM or GB standard.

05 / WIRE

Wire rod & finished wire

Diameter, surface condition, coil integrity and tensile performance are checked for the ordered product. Zinc coating inspection applies to galvanized wire where specified.

06 / BAR

Carbon, alloy & stainless bars

Diameter or section, straightness, surface finish and mechanical properties are reviewed by grade and supply condition. Hardness and ultrasonic testing can apply to specified bar orders.

07 / SECTIONS

Structural shapes

Web, flange and section geometry, straightness and cut length are checked for the ordered profile. The relevant section tolerance standard determines acceptance.

08 / PIPE

Carbon, stainless & galvanized pipe

Outside diameter, wall thickness, straightness, ends and surface condition are examined. Weld inspection, hydrostatic testing or other NDT is included when required by the pipe specification.

Dimensional & Special Inspection

Measurement and non-destructive testing where needed.

Inspection techniques are chosen for the product and acceptance criteria. Surface readings, dimensional checks and internal-condition testing address different acceptance requirements.

Ultrasonic flaw detection probe coupled to a supported steel plate surface

Ultrasonic testing of plate

Ultrasonic examination can be specified for internal discontinuities in plate. The applicable test method, inspection level and acceptance criteria are agreed before testing.

Coating thickness gauge probe touching a flat galvanized steel sheet during inspection

Coating and surface inspection

Galvanized and coated products are examined for coating coverage, surface condition and the test results required by their specifications. Coating mass and coating thickness are reported using the appropriate methods and units.

Mill Test Certificates

Traceable material. Reviewable test results.

A Mill Test Certificate links the stated grade, heat or batch identification and reported results to the supplied steel. Document requirements are confirmed at order review so that the appropriate records are available at release.

Material identificationStandard, grade and delivery state
Heat / test unitReference used for test traceability
Inspection resultsRequired chemistry, mechanical and other tests
Delivery referenceOrder, packing and release records

EN 10204 Type 3.1 is validated by the manufacturer's authorized representative independent of production. Type 3.2 includes the required additional validation by the purchaser's representative or an inspector designated by regulation. Type 3.2 must be arranged before the applicable inspection takes place.

Organized steel plate bundles undergoing traceability and shipment-document verification
Steel export packing and pre-shipment inspection at a covered industrial dispatch area

Independent Inspection & Release

Third-party inspection can be part of the order.

SGS, Bureau Veritas (BV) and TÜV inspection can be arranged according to project requirements and the agreed scope. Sampling, test witnessing, dimensional checks or pre-shipment review are planned with the appointed inspection body before the relevant activity.

Agreed inspection scopeProduct standard, test method, sampling, acceptance criteria and report type
Release documentationMill certificate, test reports, agreed inspection records and packing references
ISO 9001 & applicable CE documentsManagement-system and product documents supplied within their valid certification or regulatory scope
Export Packing & Order Checks

Procurement Questions

Confirm inspection terms before placing the order.

Inspection documents and test requirements should appear in the purchase specification, especially for critical grades and third-party witness points.

Can you provide an MTC with the steel shipment?

Mill Test Certificates can be supplied with the order documentation. Please specify the required certificate type and material standard when requesting a quotation.

What is the difference between EN 10204 Type 3.1 and 3.2?

Both report results from specific inspection. Type 3.1 is validated by the manufacturer's authorized inspection representative, independent of production. Type 3.2 requires additional validation by the purchaser's representative or an inspector designated by regulation.

Can SGS, BV or TÜV inspect the order?

Independent inspection can be arranged subject to the agreed scope and the inspecting body's availability. Any witness or hold point should be specified before testing or dispatch.

Are the same tests performed on every product?

Each order follows the tests required by its product standard, material grade and purchase agreement. Rebar bend testing, plate ultrasonic testing and coil coating inspection address different material requirements.

For Your Purchase Order

Include inspection requirements with your steel inquiry.

Send the standard, grade, size, quantity and destination along with any impact-test, NDT, coating, MTC or third-party inspection requirements. We will review the details against the proposed supply.

Material & standardSteel grade, specification and edition
Dimensions & quantityThickness, width, length, diameter, tonnes or pieces
Required testingMechanical, impact, NDT, coating or other specified checks
Documents & deliveryMTC type, third-party witness and destination port
REQUEST A QUOTE

Share your specifications or upload a purchase list. We will review the details and get back to you.


    PDF, Word, Excel, JPG or PNG. Max. 10 MB.

    Your contact information is used to respond to your inquiry. Privacy Policy.

    BAO STEEL (QINGDAO) CO., LTD. Direct factory contact · Qingdao, China
    WhatsApp